Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Spring Repair for Kirkland Homeowners
A broken garage door spring stops everything. The door won’t lift, or it drops hard and won’t stay up, and if the garage is how you get in and out of the house, the whole day shifts. Springs are also the part of a garage door that fails most often and the part most likely to go wrong when a homeowner tries to fix it alone. We handle torsion and extension springs for homeowners across Kirkland with the right winding bars, the right cables, and a clear explanation of what failed. Our technicians have up to 12 years of experience, and we work on doors from Genie, Clopay, Amarr and Wayne Dalton systems as readily as any other make. When your garage door is the problem, it’s the only problem. Call (844) 725-1599 for same-day spring repair in Kirkland.
What Our Garage Door Spring Repair Service Includes
Spring work isn’t one job. A snapped torsion spring, a stretched extension spring, a cable that’s started to fray, and a door that’s simply out of balance each need a different fix. Here’s what we actually do when we arrive.
Torsion Spring Replacement
A torsion spring is the coiled spring mounted on a metal shaft above the door, and it carries most of the door’s weight as it opens and closes. You need replacement when the spring has snapped (usually a loud bang and a door that suddenly won’t lift) or when it’s lost tension and the door feels impossibly heavy. We measure the existing spring’s wire size and length, match the cycle rating to your door’s weight, and wind the new spring with proper winding bars rather than a screwdriver or a clamp. Doors are commonly fitted with two torsion springs, and when one breaks the other has usually done the same amount of work.

Extension Spring Replacement
Extension springs run along the horizontal tracks on either side of the door and stretch as the door closes. They’re common on older Kirkland homes and on lighter single-car doors. You need new ones when a spring has stretched past its working length, when the coils show gaps, or when the door sags on one side. We replace them in matched pairs and fit a containment cable through the center of each spring so that if it ever breaks, the spring stays on the cable instead of flying across the garage.

Broken Spring Repair
Broken spring repair is the call we get most: a sharp crack from the garage, then a door that won’t budge or an opener that hums and does nothing. The opener isn’t usually the problem – it’s trying to lift a door whose spring support is gone. We confirm the break, check the cables and drums for related damage, and tell you honestly whether the spring alone is the fix or whether anything else was stressed when it let go. If the door is stuck open or hanging unevenly, we can secure it and get it back to a safe position.

Spring Adjustment
Adjustment is for springs that are intact but out of balance – the door drifts down on its own, slams the last few inches, or feels heavy to lift by hand. A door that isn’t balanced makes the opener work far harder than it should, which shortens the opener’s life. We check the door’s balance with it disconnected from the opener, then set tension so the door holds at the halfway point. This is delicate work on a loaded spring, and it’s not something to attempt with the spring under tension.
Safety Cable Installation
Safety cables are the steel cables that run through the middle of extension springs and hold them in place if they break. Many older doors were built without them, or the cable has rusted through and is no longer doing its job. We fit new galvanized cables sized for the spring and anchor them at both ends. It’s a small addition that changes what happens when a spring fails, and it’s worth doing on any extension-spring door that doesn’t already have one.
Spring Inspection
Inspection catches a spring on its way out before it strands you. We look for gaps in the coil, rust at the winding cone, a spring that’s visibly stretched, and cables with broken strands or kinks, then test the door’s balance and travel. We tell you what’s fine, what’s wearing, and what needs attention now versus later. It’s the least expensive part of spring service and often the most useful, especially on a door you’ve just moved into.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Spring Repair
Springs are largely universal in how they work, but the door and hardware around them aren’t. We work on Clopay doors and know how their panel weights and hinge patterns affect spring sizing, so the replacement feels right rather than merely functional. We service Amarr equipment and know where their track and roller assemblies wear over time. We’re also familiar with Wayne Dalton doors, including how their older spring setups differ from what a newer door uses.
That brand knowledge matters most when a door has been repaired before with the wrong spring. A spring rated for a lighter door will work for a while, then fail early and take the opener’s gear with it. We check what’s actually installed against what the door needs, whatever the make. Whether you have a Genie opener paired with a Clopay door or any other combination of makes, we can help. If you’re not sure what’s on your door, that’s fine – we’ll identify it during the visit.
Signs You Need Garage Door Spring Repair Right Now
- A loud bang from the garage. A torsion spring breaking sounds like a firecracker going off, often followed by silence and a door that won’t open. If you heard it, the spring has almost certainly failed and the door shouldn’t be run until it’s checked. Call us rather than cycling the opener to test it.
- The door won’t lift, or lifts a few inches and stops. A door that won’t come up usually has no spring support left, and the opener is trying to lift the full weight of the door. Continued attempts can burn out the opener motor or strip its gear. Stop pressing the button and let us look at it.
- The door feels extremely heavy when you lift it by hand. A balanced door should lift with one hand and stay where you leave it. If it feels like dead weight, the springs have lost tension. Don’t force it – an unbalanced door can come down hard.
- The door hangs crooked or one side lags. Uneven travel often means one of a pair of springs has broken or stretched while the other still has tension. Running the door like this twists the panels and wears the tracks. It’s a repair-now sign, not a wait-and-see one.
- Visible gaps, rust, or a stretched spring. A gap in a torsion coil, heavy rust at the winding cone, or an extension spring that no longer pulls back to its original length all point to a spring near the end of its life. Catching it here means scheduling the repair instead of dealing with a door that won’t move.
One safety note that matters more than any other on this page: a wound torsion spring and a stretched extension spring both store an enormous amount of energy, and releasing it the wrong way can cause serious injury. This is not a job for a screwdriver and a ladder. Leave the spring work to a trained technician.
Our Garage Door Spring Repair Process – Step by Step
- 1
We take the call and ask the right questions. We ask what the door did, what you heard, and whether it’s stuck open or closed so we can advise on safety before we arrive. If the door is open and won’t close, we’ll tell you how to secure the opening until we get there. We answer 24/7, and fast dispatch from 7am to 7pm gets a technician to you.
- 2
We make the door safe before touching it. The first move on arrival is to disconnect the opener and take the load off the spring system, so nothing moves while we work. That means locking the door in place and confirming it can’t travel. No one works under a loaded spring that hasn’t been stabilized.
- 3
We diagnose the whole system, not just the broken part. We measure the spring’s wire size and inside diameter, weigh the door, and check the cables, drums, rollers, and hinges for damage caused when the spring let go. That’s how we size the replacement correctly rather than matching whatever spring happened to be there. A spring that’s wrong for the door will fail early.
- 4
We replace the spring and rebalance the door. We fit the new spring (or matched pair) with proper winding bars, set the tension so the door holds at the halfway point, and run it through several full cycles. We adjust until the door travels smoothly and the opener isn’t straining. You’ll see and hear the difference before we pack up.
- 5
We test, explain, and leave you a written price. A final cycle test confirms the door opens, closes, and reverses correctly. We show you the old spring, explain what failed, and walk you through what we did. The price you agreed to before the work started is the price on the invoice. Then we’re gone, and your garage works again.
If you also need work on the opener itself, we handle that too – modern smart openers and older legacy units alike. You can see the full scope of what we cover on the Kirkland Garage Door Repair Co page.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Spring Repair Cost in Kirkland?
Garage door spring repair in Kirkland typically runs $180 – $340 for one spring, including the spring and the labor to wind and balance it. That range moves with the spring type, the door’s weight, and whether related parts were damaged when the spring broke. A matched pair of torsion springs is usually replaced together and costs about twice that. Here’s how the common scenarios break down:
| Job | Typical estimated range |
|---|---|
| Torsion spring replacement, one spring | $180 – $340 |
| Torsion spring pair, replaced together | About twice the single-spring range |
| Extension spring replacement, one spring | $180 – $340 |
| Cable repair (often needed with a spring failure) | $130 – $250 |
| Opener repair (when a broken spring burned out the motor) | $120 – $320 |
| Panel replacement (if the door came down hard) | $250 – $500 |
| Track realignment (door twisted off the track) | $120 – $240 |
What pushes a job toward the top of the range: heavy double doors, high-cycle springs, a pair replaced together, or cables that were damaged when the spring let go. What keeps it near the bottom: a single extension spring on a lighter door with everything else intact. The best way to avoid overpaying is to get the whole door checked in one visit rather than paying for separate trips – a failing cable or worn roller found during a spring repair costs less to fix then than as its own call later.
Our estimates are free. We quote in writing and agree the price with you before any work starts, so there’s no surprise invoice when the job is done. The written estimate sets the final price.
Garage Door Spring Repair Near Kirkland – Our Service Area
We cover Kirkland and the surrounding Eastside and Northshore communities, including Kenmore, Redmond, Woodinville, Bothell, Lake Forest Park, Bellevue, Shoreline and Mountlake Terrace. Most spring calls in these areas can be handled same day, and if a door is stuck open or hanging, we’ll get to it as quickly as we can. If you’re nearby and looking for garage door spring repair, the same technicians cover your area. Homeowners in Redmond can reach our garage door spring repair page for that location.
Serving Kirkland, WA – Our Local Coverage Area
We serve Kirkland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Spring Repair in Kirkland
Garage door spring repair is the replacement or adjustment of the springs that counterbalance your door’s weight so it opens easily and safely. Torsion springs sit on a shaft above the door; extension springs run along the side tracks. When a spring breaks, the door becomes too heavy to lift, and the repair restores that balance. It’s a loaded, high-tension job that needs proper tools and training. Call (844) 725-1599 for an exact quote – estimates are free.
Most spring repairs are finished in one visit, typically within a couple of hours for a single or paired torsion spring on a standard door. Extension spring replacement and safety cable work fall in a similar window. If related damage turns up – a bent track, a frayed cable, a door that came down off the rails – it takes longer, and we’ll tell you before we start. Call (844) 725-1599 for an exact quote – estimates are free.
Spring repair in Kirkland typically costs $180 – $340 for one spring, including the spring and labor. A matched pair of torsion springs is usually replaced together and runs about twice that. Cable repair, if needed, is a separate $130 – $250. The written estimate sets the final price, and we agree it with you before any work begins. Call (844) 725-1599 for an exact quote – estimates are free.
Yes. We work on Genie and Clopay systems, along with Amarr, Wayne Dalton, LiftMaster, Chamberlain, Craftsman and Raynor equipment. Brand matters less for the spring itself than for the door’s weight and hardware, and we size the spring to what’s actually installed. If you don’t know the make, we’ll identify it on the visit. Call (844) 725-1599 for an exact quote – estimates are free.
Same-day spring repair is often possible in Kirkland, especially when a door is stuck open or won’t secure the house. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician out. We’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (844) 725-1599 for an exact quote – estimates are free.
Our repairs are backed by a satisfaction guarantee, and we stand behind the work we do. If something isn’t right after the repair, contact us and we’ll make it right. Ask about coverage for the specific spring and parts when we give you the written estimate, so you know exactly what’s covered. Call (844) 725-1599 for an exact quote – estimates are free.
Clear the floor in front of and under the door, and keep vehicles out of the garage if you can. Don’t try to open the door or run the opener before we arrive, and if the door is stuck open, leave it and tell us when you call. Make sure someone can let us in and point out the door. Call (844) 725-1599 for an exact quote – estimates are free.
Schedule Your Garage Door Spring Repair Service in Kirkland Today
A broken spring won’t fix itself, and a door that won’t close is a door that won’t secure your home. Call (844) 725-1599 to book spring repair in Kirkland with a technician who works on springs and openers every day. We’ll give you a free, no-obligation estimate, agree the price in writing before any work starts, and get your door moving again. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Kirkland Garage Door Repair Co.